Crystalac Polyurethane Topcoat - Clear Gloss Finish 1 Quart

Crystalac Polyurethane Topcoat - Clear Gloss Finish 1 Quart. Extreme Protection Polyurethane is a water based interior NON-YELLOWING, Environmentally Sa

CrystaLac^® Extreme Protection Polyurethane Topcoat

Extreme Protection for Extreme Demands

Extreme Protection Polyurethane is a water based interior NON-YELLOWING, Environmentally Safe Top Coat that is Super Hard, Super Clear and Super Easy to Use.

FEATURES:

• Scratch, Chemical, and Water Resistant
• Self-Levels
• Low Odor, Low V.O.C
• Added UV stabilizers will keep dyes and stains brilliant and will help protect colors from fading
• Dries crystal clear even over white finishes. Excellent for use as a chalk paint sealer.
• CrystaLac Top Coats can be used over thoroughly dried oil or water-based stains, shellac, lacquer, Polyurethane or Acrylic.

APPLICATION:

• Can be applied by either brushing or spraying (gravity feed or HVLP sprayer)
• It is not necessary to sand between each top-coat layer. (All CrystaLac Top Coats will bond to the prior coat.)
• If recoating over an old finish, scuff sand first and remove any surface contaminants such as dirt, waxes or polishes.
• Usually 3 to 5 coats are sufficient to produce a beautiful, protective finish. Use more if desired.
• Dry time is usually 30 min to 1 hour. Allow 2 to 4 hours before recoating.
• Do not use stearated sandpaper or tack cloths. Do Not freeze. Do Not apply below 60 degrees.
• Do not thin or clean with lacquer solvents or mineral spirits. Use soap and water for clean-up.

Coverage is approximately 400 to 500 sq. ft. per gallon.

CAUTION:

Keep out of reach of children! Do not ingest. Avoid contact with skin and eyes. Do not breathe vapors. Use with adequate ventilation. When spraying or sanding, use an OSHA approved mask. V.O.C. is less than 1.4 lbs. per gallon.

DISPOSAL:

Consult your local sanitation department. Do not dump on the ground.

WARNING: CrystaLac Company has chosen to provide a warning based on its knowledge about the presence of one or more listed chemicals without attempting to evaluate the level of exposure. Products marketed or sold by CrystaLac Company may contain listed chemicals at levels that are below the Proposition 65 level of concern, or could even be zero. However, out of an abundance of caution, CrystaLac Company has elected to place the Proposition 65 warning notification on all its products. Please see our Prop 65 for specifics on these products.

Protect your wood projects and get more done, faster, with Minwax One Coat Polyurethane Protective Finish. This crystal clear protective top coat dries in just two hours and lets you complete wood projects 3x faster without sacrificing durability. The advanced formulation in this clear top coat provides the same level of durability in one coat the is comparable to three coats of a conventional polyurethane. Use it to easily protect and add beauty to your wood projects.

Minwax 356150000 One Coat Polyurethane Semi-Gloss - 1 Qt.

Extreme Protection Polyurethane Top Coat - The CrystaLac Company

Colored Polyurethane – The CrystaLac Store

CRYSTALAC Black Gloss Colored Top Coat, Mini 8 oz

CrystaLac Brite Tone Coating on Polymer Clay - The Blue Bottle Tree

Minwax One Coat Polyurethane Clear Gloss Water-based Polyurethane (1-quart) in the Sealers department at

Universal Paint Base and Primer – The CrystaLac Store

CrystaLac Polyoxide Wood Floor Finish - Gloss Finish - 1 Pint

Crystalac Extreme Protection Polyurethane 8oz Matte Satin Gloss Non Yellowing UV Resistant

Self leveling, smooth clear finish with max top coat durability - Fast dry, durable formula covers up to 125 sq. ft. per quart High clarity protective coating for indoor wood projects provides a crystal clear finish. Premium polyurethane retains the same clear finish as the day it was applied and will not yellow with time.

Varathane 1 Qt. Clear Gloss Water-Based Interior Polyurethane (2-Pack)

CrystaLac Brite Tone Instrument Finish is a super hard, scratch resistant, high solids clear finish with exceptional clarity. Of the CrystaLac line, this is by far the hardest and clearest finish. It will build to a high depth quickly due to the high solids content and will not leave a blue cast on dark exotic wood. Excellent for use on musical instruments, tables, bar tops, bowl turning and more. It adheres to wood, metal, and glass.

CRYSTALAC Brite Tone, Quart / Matte

Protect your wood projects and get more done, faster, with Minwax One Coat Polyurethane Protective Finish. This crystal clear protective top coat dries in just two hours and lets you complete wood projects 3x faster without sacrificing durability. The advanced formulation in this clear top coat provides the same level of durability in one coat the is comparable to three coats of a conventional polyurethane. Use it to easily protect and add beauty to your wood projects.

Minwax 356150000 One Coat Polyurethane Semi-Gloss - 1 Qt.

Prestect 27x6 Hi-Gloss Topcoat - Clear, Polyester

Colored Polyurethane – The CrystaLac Store